[Time]

The time of your smartphone is automatically synchronized to your Dot Watch when paired. The time function continues to operate even after the connection to the smartphone is lost. By default, the time is displayed in 24 hours.

While at “Standby” status, press the “Select Button" once to display the time. The left two cells indicate the hours and the right two cells indicate the minutes. Press the “Select Button" once more to check the seconds.

To switch the time displaying in 24 hours to 12 hours, press and hold the “Select Button” while viewing the time (hours and minutes). Press the “Select Button” to check the current second and AM or PM. Here, the left two cells indicates the seconds, and the right two cells tell “am” [dot 1, dots 1,3,4] (⠁⠍) or “pm” [dots 1,2,3,4, dots 1,3,4] (⠏⠍).

[Date]

The date of your smartphone is automatically synchronized to your Dot Watch when paired. The date function continues to operate even after the connection to the smartphone is lost.

While at “Standby” status, press the “Select Button" three times to display the current date. The left two cells reads the months, the right two cells reads the date. Pressing and holding the “Select Button” while viewing he date will switch the order of the months and date – from MMDD to DDMM.

You can also use all the basic watch functions while the Dot Watch is unpaired.

1) Press and hold both the “Select Button” and the “Home Button” at the same time to set the time manually – “set” [dots 2,3,4/ dots 1,5/ dots 2,3,4,5] (⠎⠑⠞) will appear on the screen.

2) Press the “Select Button” to set the first cell (the first digit of hours in 24, which is 0~2). Turn Dot Crown to adjust. Once set, press the “Select Button” to move on to the second cell (the second digit of hours in 24, which is 0~9). Respectively, set the third cell (the first digit of minutes in 59, which is 0~5), and the fourth cell (the second digit of minutes in 59, which is 0~9).

3) After setting the hours and minutes, press the “Select Button" and repeat the above procedures to set the seconds on the third and fourth cells: third cell (the first digit of seconds in 59, which is 0~5), and the fourth cell (the second digit of seconds in 59, which is 0~9).

4) Upon setting the seconds, press the “Select Button”, it will vibrate to signal completion of the time setting.

From the Home screen, scroll the "Crown" clockwise (upwards) twice to the Bluetooth connection status screen. Here you can check the Bluetooth connection status and try to connect

1)    Check Bluetooth connection status

When you enter the Bluetooth connection status, the following is displayed for each mode. When connected in braille mode, conn [dots 1,4/ dots 1,3,5/ dots 1,3,4,5/ dots 1,3,4,5] (⠉⠕⠝⠝) or disc [dots 1,4,5/ dots 2,4/ dots 2,3,4/ dots 1,4] (⠙⠊⠎⠉) will show.

2)    Re-sending Bluetooth Signal

If you turn on the Dot Watch and the user does not connect to the mobile device after 36 minutes, the Dot Watch stops sending Bluetooth signal. 
Press the "Select" button once to signal then connect the Dot Watch and mobile device through the application.

1) Press and hold both the “Select Button” and the “Home Button” at the same time to set the time manually – “set” [dots 2,3,4/ dots 1,5/ dots 2,3,4,5] (⠎⠑⠞) will appear on the screen.

2) Press and hold the “Select Button” to move onto the date setting. The year of the default date will appear as “2017” [dots 1,2/ dots 2,4,5/ dot 1/ dots 1,2,4,5] (⠃⠚⠁⠛)

3) Turn the Dot Crown up (+1 year) or down (-1 year) to set the year, then press the “Select Button" to move on to set the month and date.

4) Set the first cell (the first digit of months in 12, which is 0~1). Turn Dot Crown to adjust. Once set, press the “Select Button” to move on to the second cell (the second digit of months in 12, which is 0~9). Respectively, set the third cell (the first digit of date in 31, which is 0~3), and the fourth cell (the second digit of date in 31, which is 0~9).

5) Upon setting the last cell, press the “Select Button”. The device vibrates, and date setting (month and date) is completed.

While the device is paired with your smartphone, you can be notified of incoming calls on its braille display. Upon receiving a call, the device will vibrate repeatedly and “call” [dots 1,4/ dot 1/ dots 1,2,3/ dots 1,2,3] (⠉⠁⠇⠇) appears.

Press the “Home Button” to reject the call immediately, or press the “Select Button” to check the caller information. If the contact is saved on the smartphone, you can check the caller's name in Braille. If the contact is not saved, you can check the number in Braille. Use the “Touch Sensor” to view the caller information.

While checking the caller information, press the “Home Button” to reject the call, or press the “Select Button” to answer. Please note that the Dot Watch does not have a microphone! You will need your smartphone to carry out the call after receiving it.

(iOS) While checking the caller information, press the "Select Button" to receive the call, or press the "Home Button" to reject the call. Receiving or declining a call will take the device back to its “Standby” status.

(Android) Depending on your smartphone, reception and rejection functions may be restricted.

Follow the guideline below to use the Stopwatch function. The stopwatch will still run in the background when left un-paused. The four cells will display minutes and seconds up to 59 minutes and 59 seconds. From 1 hour and on, the four cells will display only the hours and minutes.

1) From the “Standby” status, turn the Dot Crown downward twice to access the stopwatch function – “stop” [dots 2,3,4/ dots 2,3,4,5/ dots 1,3,5/ dots 1,2,3,4] (⠎⠞⠕⠏) will appear on the screen.

2) Press the “Select Button” to enter the stopwatch – “0000” [dots 2,4,5/ dots 2,4,5/ dots 2,4,5/ dots 2,4,5] (⠚⠚⠚⠚) will appear on the screen.

3) Press the “Select Button” to start/pause/resume the stopwatch.

4) Press and hold the “Select Button” to reset – “0000” [dots 2,4,5/ dots 2,4,5/ dots 2,4,5/ dots 2,4,5] (⠚⠚⠚⠚) will appear on the screen.

5) After 59 minutes and 59 seconds, a new cycle begins from 0 seconds.

Follow the guideline below to use the Timer function (the count limit is 59 minutes and 59 seconds). The timer will still run in the background when left un-paused.

1) From the “Standby” status, turn the Dot Crown downward 3 times to browse the timer function – “timr” [dots 2,3,4,5/ dots 2,4/ dots 1,3,4/ dots 1,2,3,5] (⠞⠊⠍⠗) will appear on the screen.

2) Press the “Select Button” to enter the timer. Here, the left two cells are indicate the minutes, and the right two cells indicate the seconds. Turn the Dot Crown to set the digit, and press the “Select Button” to move onto the next cell. After settings the seconds, press the “Select Button” to start the countdown.

4) While counting down, press the “Select Button” to pause. Press it again to resume.

5) When the countdown is completed, timeout “tout” [dots 2,3,4,5/ dots 1,3,5/ dots 1,3,6/ dots 2,3,4,5] (⠞⠕⠥⠞) will appear with vibrations to notify. Press the “Home Button” to dismiss the timer notification, or it will be dismissed automatically after 5 minutes.